Shop
This is where you can browse products in this store.
-
Pot Joint Removing Tool Made By Minispares
- R747.28 excl VAT
- Inboard CV (pot joint) splitting tool used to remove the constant velocity joint from the gearbox by way of driving this wedge-like tool between joint and gearbox. Does not remove joint from driveshaft.
-
Brake Caliper Bridge Seal – Cooper &Cooper S
- R108.52 excl VAT
- Genuine oil seal between the two halves of the original cooper S caliper and is only supplied by Rover. AP suggest you should buy the bolts to hold the 2 halves together as well when undertaking this repair, see 17H8765. Sold singly.
-
Heater Matrix Radiator 1963 Up to 1968/69
- R2,559.44 excl VAT
- The heater is not available any more, but this matrix is the main component which gets blocked up or leaks, stopping it blowing hot air. This is a new heater matrix for late MK1 plus MK2 cars has 4.5" gap between pipes with opposite outlets for cars up to MK3, which have the outlets fitted the opposite side. A few…
-
Plug – Screwed – 997,998 & 8.4” Brake Caliper
- R153.09 excl VAT
- This holds the brake light switch(C16062A) on single line brakes and fits into the 2 way union where the front hose bolts on the other end.
-
Early Mk1 Heater Matrix 59–63 Only
- R3,736.40 excl VAT
- The heater is not available anymore, but this matrix is the main component which gets blocked up or leaks, stopping it blowing hot air. This fits the early Mk1 cars only with 5" gap between pipe hole centres, after 1963 17H8608 was fitted with 4.5" gap between pipe hole centres.
-
Master Cylinder Metal Cap Original Type
- R179.20 excl VAT
- Replacement metal master cylinder cap as originally fitted to 1959-1963 Minis on single line brake systems is a great historic feature.
-
Bumper With Holes for Corner Bars – Stainless Steel
- R2,668.90 excl VAT
- Stainless steel with corner bar holes. Any Mini with "corner bars" on the bumpers was probably considered a Deluxe model such as a Cooper S. If you want to restore your Deluxe or upgrade your standard you need these stainless steel bumpers with correct size holes in the right place for the corner bars. These bumpers like all genuine type…
-
Boot Board Side Support Brkt
- R278.42 excl VAT
- When a boot board is fitted the following brackets are required: 14A9780 x 2 U shaped for the rear to hold the board. 14A9781 x 2 side bracket with plug for board to sit on except elf/hornet. 14A9782 x 1 centre bracket with support buffer. A complete kit is available as CCC115. uses ALH1473 buffer when required as a spare…
-
Front Boot Board Bracket
- R222.30 excl VAT
- When a boot board is fitted the following brackets are required: 14A9780 x 2 U shaped for the rear to hold the board. 14A9781 x 2 side bracket with plug for board to sit on except elf/hornet. 14A9782 x 1 centre bracket with support buffer. A complete kit is available as CCC115. See CCC115A when any 165 tyres are fitted.…
-
Panel Hinge Inner R/H A Panel External Hinge Type
- R1,070.80 excl VAT
- For minis with sliding windows and external door hinges. This is the inner hinge panel with the brackets on to reinforce the areas where the hinges sit. You will require the outer panel also 14A6901 for R/H and 14A6902 for L/H
-
Door Drain Tube for External Hinge Type Door
- R129.40 excl VAT
- These special hoses are for all sliding window type doors to drain the water away from the channels. The thin end of the hose slides into the bottom tube to ensure water goes out and cannot leak into the bottom of the door and the top slides over the upper drain pipe tube.
-
Grille End Moulding Mk1 L/H
- R417.60 excl VAT
- Whiskers were so rare for so long, many of us forgot that our MKI Minis ever had them. If you still have the empty clips, you just need the whiskers, if you need clips they're ADA3583. The rivets to hold the clips are RA608076. This fits the left side.
-
Grille End Moulding Mk1 R/H
- R417.60 excl VAT
- Whiskers were so rare for so long, many of us forgot that our MKI Minis ever had them. If you still have the empty clips, you just need the whiskers, if you need clips they're ADA3583. The rivets to hold the clips are RA608076. This fits the right side.
-
Check Strap Retainer Plate Mk1/2
- R62.94 excl VAT
- This plate has recessed holes in for the check strap screws. 2 per door are required and these are only for cars with external hinges that had the material check strap as per MK1/2 and vans.
-
Mk 1/2 External Hinge Angled Spacer
- R28.11 excl VAT
- Angled spacer washer for Mk1/2 external door hinge cars for the upper hinge
