Boot
Manifold Stud. Suitable for All Non Injection Minis
- R21.15 excl VAT
- Manifold stud 39mm long for all A series engines up to injection which use LYR10028 which is 6mm longer at 45mm.
Boot Lid Cable (Single)
- R90.42 excl VAT
- These two simple cables are all that keep the boot lid from crashing down, damaging hinges, bumper and paint. When one fails we recommend replacing both to be sure of the same length sold singly 2 required per car. 37H3043 can be used to replace the plastic spacer if required as they are often broken or missing on later cars
Boot Lid Seal Clip for 14A6584 (26 Required)
- R17.53 excl VAT
- Used on all MK1/2/3 bootlids where there are 26 little holes drilled around the inner edge. These are for use with 14A6585 seal--- Later cars 1988 on fitted a seal to the body only (cke10018)
Door Gasket External Hinge Large End On Door
- R18.64 excl VAT
- THIS IS THE LARGE GASKET THAT FITS BEHIND THE HINGE ON THE DOOR OF AN EXTERNAL HINGE ON CARS WITH SLIDING WINDOWS SUCH AS MK1/2. SEE BMP135 FOR SMALL ONE.
Rubber Grommet for Floor Pan & Boot Floor 1″ 25 mm
- R44.11 excl VAT
- Special shape and strength 1" rubber floor plug. Also speedo cable unused hole where shells have holes for LHD and RHD.
Boot Hinge Gasket Lower
- R14.47 excl VAT
- These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
Boot Lid Hinge Gasket Upper
- R13.91 excl VAT
- These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Boot Seal Clip Kit
- R328.26 excl VAT
- Introduced by the factory to eradicate water getting to the electric coils causing breakdowns this was used up until they introduced the plastic engine protection shield but many owners still played safe and fitted one anyway. Note: The kit contains 26 clips needed for 1 car
Boot Lid Seal Early Type (Requires 26 X 14A6585)
- R329.74 excl VAT
- Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid all the way round. Fitting the wrong way round makes it very difficult to close lid…
Bonnet Strap Tan Original Works Type-Single Strap
- R397.04 excl VAT
- This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. Original light colour Tan leather 3.3mm thick from the tanneries for use on horse bridles, with alloy fastening. Screws included. Mini Spares have been supplying these original looking type for over ten years so beware of copies which are thinner with inferior…
Bootlid Number Plate Buffer
- R62.94 excl VAT
- All Mk1/2 had a hinged number plate on the bootlid and these are the buffers that protect your paintwork and help locate the number plate at the correct angle. 2 required per car, sold individually.
Mini Cooper Laurel Winged Badge 1996 On
- R772.25 excl VAT
- Genuine Bonnet and Boot stick on wreath type Mini Cooper badge similar to those fitted from 1996 on-classic mini only supplied by Rover
Bootlid Seal, 1988 to 2000
- R297.72 excl VAT
- This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.
Leather Bonnet Strap Tan
- R420.00 excl VAT
- Locally proudly Heavy duty Leather Bonnet/Boot Strap.
Barrel Lock Set for Push Button Type Door Handles 1970 on
- R570.05 excl VAT
- Key barrel set for Mk3 onwards door handles and boot handles.
