Bearings
-
Needle Roller 1st Motion / Layshaft 4 Sync
- R124.86 excl VAT
- Dual use bearing fits the end of the A Plus 18mm mainshaft where the Ist Motion shaft slides on, plus it is used on the A Plus layshaft smaller end. Known as the 18mm bearing it was Rovers upgrade on using larger mainshafts and laygears with 3 step layshaft. CHM141 still fits the larger end of 4 Synchro layshafts. Original…
-
Gear Change Bush. Pre Rod For Gearbox Linkage Rods
- R131.97 excl VAT
- The bronze bush in the differential housing that the gear change selector rod sits through which should be lightly greased.
-
Pre A+ 1st Motion Needle Roller
- R109.60 excl VAT
- This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on. This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the fixed sleeve type bearing 22G314, they have been obsolete from the manufacturer for many years. Unless…
-
Single Row Rhp Roller 4 Synchro
- R1,078.80 excl VAT
- Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft. This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to replace it again let alone any further damage that can happen, it is not worth taking the risk. We try and…
-
Needle Roller 1st Gear Only
- R396.46 excl VAT
- 1ST Gear needle roller bearing, 4 Synchromesh only Sits on the top hat sleeve that locates 1st gear.
-
Diff Side Cover Plate Bush Std Mini
- R96.40 excl VAT
- You require 5 of these high tensile short head studs and they torque to 42lb per sq ft. See also complete kit which includes these top grade studs C-AHT279. 3/8"unc stud with unf end for head nut and is 4" long. See other long head stud CAM150 5.75" long. Cooper S requires head bolt C-AHT281.
-
Needle Roller 2Nd And 3Rd Gear
- R367.59 excl VAT
- Needle roller bearing on 4 synchromesh gearboxes for 2nd and 3rd gears, 2nd gear needs split bearing.
-
Idler Needle Roller Bearing For A Plus Gearbox
- R294.58 excl VAT
- Torrington/Koyo idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bearing AHU1707. 35mm wide which takes the 22.225mm idler gear shaft on all A plus gearboxes.
-
Gearbox 4 Sync A Plus Rebuild Kit Less Diff 18 mm Mainshaft
- R7,922.84 excl VAT
- Full rebuild kit less diferential parts with competition layshaft and EVO baulk rings. Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use. This is a full kit of bearings except the 3 rollers under 1st/2nd and 3rd gear which often do not get checked…
-
Gearbox 4 Sync Rebuild Kit Less Diff Pre A Plus Std Layshaft
- R7,055.42 excl VAT
- Full rebuild kit less differential parts, supplied with standard layshaft Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use. This is a full kit of bearings except the 2 rollers under 1st and 2nd gear which often do not get checked(available as AAU1815-AAU1816). Complete…
-
Primary Gear Front Floating Bush 1275cc
- R52.32 excl VAT
- Ideal for use on the stepped type 1275cc type cranks this bush is fully floating and does not require the extra costs of fitting and machining. Always ensure that the bush buts up squarely to the shoulder with the oil holes in the trough and not on the edge of the stop step, as the oil drain holes can act…
-
Locknut (Gae191) 3/8″Unc
- R17.53 excl VAT
- Special flat 3/8" UNC nut for the reverse light switch GAE191.
