Shop
This is where you can browse products in this store.
-
Door Handle Kit Inc Boot Handle for Pre 1966 Mk1
- R3,181.40 excl VAT
- Full Mk1 door handle set with 2 front door locking handles and boot handle with matching keys.
-
Mainshaft Early 4 Synchro
- R2,925.76 excl VAT
- 4-synchromesh mainshaft for gearbox transmission with 14MM nose (13.97MM)0.550" required for either 1st motion shafts 22G1371 or 22G1093. This is Pre Aplus. See 22G833MS when no stock Reference=3 synchro mainshaft 22G392 is shorter and so is the 18mm nose late 4 sync mainshaft DAM7484 2G833 total length 26mm (10.24")
-
Heater Fascia Panel – Single Speed – Black
- R587.20 excl VAT
- Heater fascia plate for use with the single speed heaters prior to around 1995. Not suitable for late model Spi cars or Mpi. The panel fixes to the heater using an adhesive pad on the rear of the panel. Available polished or anodised in black, blue, red or silver. Weight: 36g Weight includes all fixings as shown (no tools or…
-
Ring Gear Thin For Inertia Starters (Not Pre Engaged Types)
- R876.00 excl VAT
- The thin ring gear is for old type inertia type starters and used on our steel flywheel C-AEG619 and C-AEG421. Originally fitted to automatic cars and old cast flywheels when lightened by various tuning shops in the 79s and 80s which is not recommended for competition. 107 teeth.0.343"wide
-
Differential Pin Genuine
- R725.50 excl VAT
- Genuine Rover Tuftrided diff pin, as fiited to all the later A+ gearboxes as a standard upgrade. These are the last genuine parts left and will not be available again
-
Genuine Rook EE Wood 3 Clock Surround Insert for Classic Mini
- R100.00 excl VAT
-
Gasket Lower Diff Case Housing – Rod Change
- R15.58 excl VAT
- Lower gasket for the differential housing gasket for all rod change gearboxes, the upper is 2A3505B. Remote and magic wand gearbox lower gasket is 2A3506B.
-
Locknut (Gae191) 3/8″Unc
- R17.53 excl VAT
- Special flat 3/8" UNC nut for the reverse light switch GAE191.
-
Cooper S Output Shaft Bolt In En24x
- R93.21 excl VAT
- There are 4 of these to each output flange to which the Hardy Spicer joint bolts. The special philidas nuts for these are our number‚ GFK3431.
-
Front Hub Nut CV Joint Drum Brake / 7 Inch Cooper Disc
- R82.95 excl VAT
- Front hub nut that screws onto the CV joint of all early minis with drum brakes plus all standard cooper 997/8 models. 1 1/8, 1.125" AF nut size although 28mm width have been seen. The washer for this is‚ 2A7323.
-
Poly Upgrade Track Rod End/Knuckle Gaiter
- R73.46 excl VAT
- Polyurethane upgraded gaiter for all knuckle joints and many track rod ends For standard rubber versions see 21A425 please note- this does not fit all track rod ends as so many genuine and aftermarket parts have been supplied in 60 years. It does however fit every suspension knuckle ball joint GSV1118 ever made. Current rubber gaiters seems to have short…
-
Petrol Tank S/Steel Van Pickup & Estate
- R6,362.00 excl VAT
- Stainless steel Non Genuine reproduction tank is in automotive stainless steel and fits all the long wheel base Minis, except for the very early side-tank travellers. Also used on many kit cars and specials owing to its shape. Because of the outside location of these tanks, the originals seem to take a real beating and are prone to rust. Genuine…
-
Bracket Lower Steady Rod Lh
- R140.54 excl VAT
- Used in our‚ MSSK001‚ left hand lower engine stabiliser kit this bracket fits to the subframe and the gearbox.
-
Drive Flange 8.4 Disc Upgrade
- R1,058.56 excl VAT
- This drive flange fits all cars fitted with 8.4" disc brakes except Turbos. Originally intended to use 12" wheels it is an integral part of the front suspension. Sold singly 2 required per car. In addition to providing the connection between the axle and the wheels (thus the term "drive flange") it also provides the outer thrust surface for the…
-
Engine Mounting. 2 Piece Poly Mounting Manual Only
- R247.98 excl VAT
- Made in Poly this mounting comes in 2 halves held by a large clip which helps engine removal. We will honestly state that they are not easy to fit and are thicker than the originals which causes a bit more grief. Longer bolts maybe required as well. They also seem to transmit more engine noise on tickover. Choose 21A1902 originals…
