Mini
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
-
Ring Gear for Inertia Starter Motor / Not for Steel Flywheel
- R823.62 excl VAT
- Rated 0 out of 5
- Half inch wide ring gear with chamfered teeth to accept early inertia type starter motor engagement - used until the introduction of pre engaged starters with the built in solenoid from about 1984 on. 107 teeth For autos see 22G2613.
-
Distributor 1275GT Any 1300 Pre A Plus 41419
- R1,731.20 excl VAT
- Rated 0 out of 5
- Range of distributors with modern day curves built,programmed and tested for Mini Spares in UK. Beware of cheap China made units that are poorly made- see note at bottom. GEU930 25D 850/early 998 12G2140 23D Cooper S non vac BAU1962 45D 998/1098 ADU5789 59D 998 A plus 12G4180 45D 1275cc with vac, good for modified road tune engines ADU3825 59D…
-
Engine Oil Gallery Plug In Block
- R45.37 excl VAT
- Rated 0 out of 5
- Brass type core plug for engine. Originally, engines had brass oilway plugs (2K1345) 1/4" hole fitted. These cup type plugs replaced them about 1985. 12.7mm cup type plug about 9.6mm deep. Fits 1/2" hole. All good engine tuners would remove them for cleaning sludge but these later cup type are much easier to remove and replace. 4 required ON LARGE…
-
Coil Bracket 1969–95 Lucas Type Coils Stainless Steel
- R261.38 excl VAT
- Rated 0 out of 5
- Stainless steel coil bracket for 1970-1996 cars.
-
Locating Ring – Inlet Manifold to Cylinder Head
- R53.12 excl VAT
- Rated 0 out of 5
- Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the head and usually the inlet manifold to take these spacers.
-
Cylinder Head Take Off In Alloy 5/8″ Bore
- R671.39 excl VAT
- Rated 0 out of 5
- Alloy CNC version of the cylinder head take off‚ 12G2534. The standard item being steel can be prone to corrosion, this CNC alloy version is smart, and will not corrode like steel does
-
Cylinder Head Heater Take Off
- R225.45 excl VAT
- Rated 0 out of 5
- Once the old type alloy heater valve on the head was discontinued in 1990 for the plastic free floating inline type this take off union was fitted in its place on A series engine cars for use with the larger 5/8" hose. Uses‚ 88G221‚ gasket.
-
Distributor 23d Electronic Neg Earth
- R2,204.48 excl VAT
- Rated 0 out of 5
- NEGATIVE EARTH ONLY. Cooper"S" 23D distributor, no vac unit-This is NOT THE ORIGINAL LUCAS ITEM but a new contact less electric copy of 40819 to cope better with modern day fuels. Fitted with the better Red rotor arm upgrade.Cheaper than many electronic ignition kits. For best performance and tune we advise our electronic evolution version‚ C-27H7698‚ in a 45D body
-
Alloy Mounting Block(Used Part Only) Brkt to G/Box Takes
- R442.04 excl VAT
- Rated 0 out of 5
- Alloy bracket on the end of the gearbox for supporting the lower radiator bracket‚ 12A361‚ to mount on. Second hand "USED" parts only as Rover no longer have stocks--cleaned but they are old used items but all perfectly servicable
-
Bush – Small End – 998 & 1098cc
- R81.91 excl VAT
- Rated 0 out of 5
- BUSH-SMALL END-998 & 1098CC
-
Dipstick Tube Nylon Pre A Plus
- R219.82 excl VAT
- Rated 0 out of 5
- Plastic dipstick tube fitted to early cars pre metal dipstick tube.
-
Engine Lower Radiator Bracket
- R1,695.12 excl VAT
- Rated 0 out of 5
- Engine mounting bracket on the end of the gearbox which also holds the radiator support bracket. This fits to the alloy bracket‚ 12G1318‚ on the front cover of the gearbox.
-
Fan Spacer (4 mm)
- R159.97 excl VAT
- Rated 0 out of 5
- Used with most of the standard fans, definitely required if you have a breather type timing cover. This spacer is: 4.05mm thick/0.162"
-
Lower Radiator Bracket 1974 On
- R328.97 excl VAT
- Rated 0 out of 5
- this lower radiator bracket originated when the one piece rad cowling was introduced
-
Upper Rad Brkt 850/998 Up to 1974
- R253.80 excl VAT
- Rated 0 out of 5
- Upper radiator bracket, not painted,original on all small bore engines with 2 piece rad cowling. Is yours cracked at the bolt holes? This is the original with complete width stiffener plate where seals fit and has cut-away bend for strength as fitted by the factory 1974-80 but the 850-998cc all fit the same--this is not powder coated-for black painted version…