Clutch
-
Clutch Plate Road/Rally 180 mm Made By Ap Racing
- R3,031.44 excl VAT
- High performance plate- from the old AP Racing division. Bonded rally/race type 180mm wide clutch plate which is ideal for fast road and track days. This was the most commonly used performance plate from the AP Racing section and originally claimed good for 140ft lbs, but see the new Mini Spares/AP clutch plate C-AHT595 tested to 10,000rpm and destruction by…
-
Clutch Plate Verto Performance Plate 190 mm Wide
- R1,875.19 excl VAT
- Performance clutch plate for road and rally Verto type - see also 20% upgraded pressure plate
-
Pressure Plate Lightened En8 for Competition Pre Verto
- R3,264.80 excl VAT
- Pre Verto type clutch. This is a lightweight version of the pressure plate for diaphragm clutches and made in an upgraded material EN8 steel for competition use. Also in EN8 is 22A598 which should be used for road use as a replacement for the original 22G270 or 22A598 cast backplates, nearly 2lbs heavier. This C-AHT230 weighs 1.291(2.846lb) or 1.32kg (2.91lb).
-
Ultralight Steel Flywheel Pre-Engaged Starter
- R4,439.36 excl VAT
- Ultra light billet EN8 steel race flywheelfor diaphragm clutch [NOT Verto] with ring gear for pre-engaged starter. The latest refinement of the Ultra-light Mini flywheel is that it is now made symmetrically to reduce harmonics vibrations caused by earlier versions identified by their large 3 slots, rather than the current 6 smaller slots- yet it still weighs just over 3.66kg…
-
Ultralight EN8 Steel Flywheel 3.8kg Inertia Starter
- R5,148.80 excl VAT
- Ultra light (3.87kg - 8.53lbs) EN8 steel billet race flywheel for diaphragm clutch {NOT-Verto} with ring gear for non-pre-engaged starter .Forged is more rigid at high speed. The latest refinement of the Ultra-light Mini flywheel is now made symmetrically to reduce harmonics vibrations caused by earlier versions (those with just 3 large lightening slots)- yet it still weighs under 4kg.!…
-
Verto Performance Clutch Cover
- R1,987.44 excl VAT
- Verto 20% upgraded performance pressure plate which should be used with 190mm organic clutch plate‚ C-AHT594‚ or the paddle type drive plate as used in racing‚ C-AHT600. This pressure plate has a blue paint identifying mark and can be used on any Verto clutch MPI /SPI including Turbos as it offers an upgrade but check flywheel for wear if changing…
-
Flywheel Steel SPi Only
- R5,507.86 excl VAT
- This is for single point injection cars. should be balanced with pressure plate. This flywheel must use a VALEO PRESSURE COVER or Minispares C-AEG485 with 20% upgraded pressure or the car WILL NOT START because the timing slot will be out of line. This has 2 oval timing holes. For best results use clutch plate C-AHT594 or C-AHT596. This lightened…
-
Flywheel Steel MPi Only
- R5,420.72 excl VAT
- MPI flywheel, must use VALEO pressure plate/or‚ C-AEG485‚ Minispares uprated pressure plate OR THE ENGINES WILL NOT START BECAUSE THE TIMING SLOT WILL BE OUT. Twin point injection cars had 190mm clutch plates. C-AHT594(190mm wide or C-AHT596 (180mm wide) race rally clutch plates are recommended. For real competition work see C-AHT600 sintered plate. This flywheel is machined to increase clamping…
-
Flywheel Verto Lightweight Which Also Upgrades Clutch Also
- R4,723.33 excl VAT
- For pre injection Verto clutch cars with pre engaged starter, it is also designed to increase clamping pressure which effectively upgrades the actual performance of the verto clutch, which with the AP pressure GCC679 (part of GCK151MS) exceeds all previous high clamping pressure plates except for our new C-AEG485 which is 20% upgraded.
-
Steel Flywheel – C-AEG421 Type for Pre-Engaged Starter
- R4,373.66 excl VAT
- Steel diaphragm type flywheel, road use weight, and only for use with pre engaged starter. Cheaper than a standard replacement from Rover If you have the old inertia type starter use C-AEG421
-
Clutch Flywheel Bolt. Short Race Use – Sold Singly
- R103.23 excl VAT
- Race quality bolt-sold seperately- these shorter bolts hold the spring straps‚ 2A3658‚ to the flywheel on diaphragm type flywheels only. Not for Verto flywheel. Only tighten up to 16lbs per sq foot torque when using shake proof washer or 18lbs if using flat washer and locktite ---
-
Clutch Bolt Long Cover To Pressure. Race Use Single Bolt
- R125.80 excl VAT
- Race quality shoulder bolts for the Mini clutch backplate to the diaphragm--sold seperately- heavy duty racing type EN16 tightenn up to 16lbs per sq foot torque when using shake proof washer or 18lbs and locktite. Use with‚ C-2A3659‚ race quality bolts
-
Clutch Lever Arm and Plunger Race Kit
- R2,307.60 excl VAT
- Race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.
-
Clutch Sleeve A Plus
- R734.20 excl VAT
- Sleeve that covers the flywheel bolt on verto clutches for the release bearing Note--early 58mm internal diameter sleeves had a plastic anti rattle sleeve which is no longer available but this later type is smaller in diameter and therefore does not require the sleeve.
-
Metro Clutch Damper
- R1,130.64 excl VAT
- Clutch damper,only used on early metros.Slave cylinder has a larger hole for the hose.Do not use on mini.
