Clutch
-
Clutch Flywheel Strap Bolt Short – Torque to 16lbs Only
- R65.11 excl VAT
- There are 3 of these shorter 5/16"unf bolts holding the spring straps‚ 2A3658‚ to the flywheel on diaphragm type flywheels only. Not for Verto flywheel. Only tighten up to 16lbs per sq foot torque when using shake proof washer or 18lbs if using flat washer and locktite. The steel used is EN1A leaded which is a low carbon free cutting…
-
Clutch Bolt Long Cover to Pressure Torque to 16lbs Only
- R75.48 excl VAT
- Shouldered 5/16"unf bolts for the Mini clutch backplate to the diaphragm, not for heavy duty use or racing. Only tighten up to 16lbs per sq foot torque when using shake proof washer (GHF323) or 18lbs if using flat washer and locktite. Only use‚ C-2A3657‚ for anything other than standard as this is flanged and in high grade material.
-
Clutch Master Cylinder Gasket
- R44.33 excl VAT
- This gasket sits under the clutch master cylinder. For brake master cylinders see 31G840.
-
Clutch Throw Out Locknut for 22A180 Plunger
- R52.88 excl VAT
- The locking nut for the clutch throw out plunger‚ 22A427
-
Flywheel Keyway – Pre Verto (Made In En24T Steel)
- R309.20 excl VAT
- Made in EN24T for strength they have been made to fit the majority of flywheels that seemed to slightly differ from the mid 60s. Run a file down the raised keyway if tight. This flywheel locking plate is for pre verto diaphragm clutches. For Verto type see‚ DAM5923.
-
Clutch Hose Braided One Piece. Clutch Master To Slave Cyl
- R830.50 excl VAT
- Delete the metal pipe and existing hose by fitting this longer one piece steel braided pipe which can be used for either early or verto clutches. A sensible modification for all mini owners.
-
Flywheel Bolt Pre Verto
- R288.12 excl VAT
- The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by‚ 22A1155‚ locktab on the‚ 88G508‚ key washer.
-
Clutch Return Spring Anchor for Genuine Clutch Arm
- R133.90 excl VAT
- This plate is on the end of the PRE A plus original long type clutch arm‚ 22A2204‚ to hold the return spring‚ 1G5999. The clevis pin to hold this on the arm is‚ CLZ518. If you have the later Mini Spares arm with 22A2204 stamped on side with a square end you require [link2A3601MS[/link].This plate is 20mm wide spring end…
-
Clutch Plunger Uprated Pre Verto Made In En24
- R607.72 excl VAT
- Upgraded pre verto clutch lever arm plunger. Surely to be copied by competitors as the early diaphragm clutch really needed a quality item to be remade. This is the carrier that holds the clutch release bearing and on the other end has a hole for the clutch lever arm‚ 22A2204MS. Manufactured in the UK for Mini Spares quality product range.
-
Clutch Push Rod
- R173.11 excl VAT
- The push rod on your clutch arm held in by clevis pin‚ CLZ518‚ that goes into the slave cylinder. Check the eyepiece for wear. The same push rod was fitted to both Verto and Pre verto slave cylinders.
-
Mini Pre Verto Clutch Kit
- R1,962.80 excl VAT
- Clutch Kit 3 Piece Diaphragm Type – Pre Verto Type Classic Mini Clutch Kit 3 Piece Diaphragm Type - Pre verto type 1964-1982
-
MED HD CLUTCH ARM
- R2,687.50 excl VAT
- The MED heavy-duty clutch arm is machined from EN24T steel, which is then heat treated for added strength and longevity. The design swaps the standard ball end for a full-width cam section, with a special plunger to suit. This is far stronger than the standard setup, which is prone to premature wear of the ball. With uprated competition clutch setups,…
-
Med Pre-Verto F/W Bolt And Washer
- R1,009.90 excl VAT
- The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximize strength. After machining, the bolt is then heat treated to 'X' condition for maximum strength. To complete the kit, the Key washer is CNC machined from the same EN24T steel, which is then heat treated for extra strength.
-
Verto Clutch Release Thrust
- R225.45 excl VAT
- If your late model Mini has a short (3" or so) clutch arm, you have a "Verto" clutch. This is your release (throw-out) bearing. Also see‚ DAM2413‚ clip which should be changed everytime. There is also a seal‚ AAU2866.
-
Nut Nyloc 5/16″ UNF
- R9.20 excl VAT
- Zinc Plated 5/16" UNF Nyloc nut.
