Shop
This is where you can browse products in this store.
-
Kad CV Taper Washer
- R256.41 excl VAT
- KAD own design CV Taper Washer. We have made them without the split, this stops them from closing up under cornering pressure and momentarily loosening the wheel bearing. We have tested them over the last few years with great success! Sold individually.
-
Kad Alloy Race Flywheel and Backplate Combo
- R14,865.44 excl VAT
- This flywheel and back plate is CNC machined from 7075T6 aero grade aluminium alloy which gives them the strength to handle big power whilst remaining light enough to allow fast engine acceleration. Since 2004, the flywheels and back plates are supplied with bolt in friction linings which allow user replacement if wear occurs. Both organic and sintered clutch plates can…
-
Mini 52cm Necklace Gold Plated
- R400.84 excl VAT
- gold plated necklace with miniture mini for the fashionable owners
-
Bonnet Front Drain Seal
- R212.92 excl VAT
- This is the seal that goes on the front of the bonnet to stop rain getting at your electrics or causing rust and was fitted to every mini and Clubman.
-
Chrome Mk3 Onwards Locking Boot Handle
- R597.00 excl VAT
- Mk III Chrome boot handle as fitted to all saloons from 1970 on. Includes 2 keys and paper gaskets.
-
Heater Valve Twin Point Only Fitted On Side Of Heater Unit
- R450.90 excl VAT
- Twin point Mini heater tap that fits to the heater assembly
-
Heater Valve In Line Type From 1989 to 1996
- R514.72 excl VAT
- From 1989 until the introduction of the twin point injection cars, Rover fitted this in line floating heater valve which was the first time they never bolted the heater valve as a direct outlet on the cylinder head. A strange looking black plastic valve to control the water to the heater.
-
Heater Control Cable.Twin Point Cars 1996 On
- R352.01 excl VAT
- This cable is for twin point injection cars only-19"long
-
Heater Control Cable SPi (42.250″Long)
- R356.24 excl VAT
- The single point injected used this very long cable,10" longer than previous models so if you need an extra long cable this will fit. It's now 42.25". Has the old logo as per CHM373 and a loop on the end to fit later in-line heater valves. Your original logo can be fitted by pushing new one out carefully if you…
-
Heater Cable Floating In Line Plastic Heater Valve 88–91
- R328.40 excl VAT
- This very late model heater cable 31.25" long with a loop on the end was used on 1988 models with a plastic in line heater valve only up to introduction of the single point injection, useful option for those with unique needs. A unique features includes a special hook on the end of the cable is required on all later…
-
Motif for Heater Cable 1990on Red and Blue Arrow Emblem
- R93.15 excl VAT
- first used in 1990 but can be used on earlier cables and it shows HOT and COLD displayed by red and blue arrow heads
-
Heater Matrix Radiator 1991 On Plastic 90° Outlets
- R1,369.28 excl VAT
- The heater outlets exit on L/H and are horizontal for 5/8"hose fitting. The outlets for this mod come seperately, as part number JEP10008.
-
Castrol Classic Oil Pump Can
- R357.00 excl VAT
- Classic Castrol oil can with flexible spout and thumb pump.
-
HT Lead Set Red Silicone From Luminition
- R919.51 excl VAT
- 100% silicon insulation, silicon coated suppressed conductor,braided glass reinforcement,increased working temperature 0f minus 50C to +300 degrees with improved resistance to damp and water, great fitting and spiral bound wire giving instant and greater resonance. 7-8mm and dull colour red.
-
Sump Plug Oil Temp Adaptor Female – Male (Read Notes First)
- R260.56 excl VAT
- A union to fit the sump plug hole to accept Smiths oil temperature gauges, but will only take the small capillary type bulb as used on very early and current smiths oil temp gauges, does not fit the larger capillary fitted to some smiths gauges unless you have the hole machined out larger.
