Shop
This is where you can browse products in this store.
-
Rear Subframe Small Rubber Mounting Bush
- R58.96 excl VAT
- Minis Spares product to a slightly higher modern day shore hardness and texture soecification. Pre 1976 used 8 of these bushes for the trunnions on the rear subframe but from (MK4)1976 on Rover reduced the quantity to 4 and used 2 larger bushes 21A2560 on the new front trunnions 21A2558MS. Manufactured in the UK.
-
Gear Lever Knob Mk 1 & 2 Mini
- R338.00 excl VAT
- Reproductions of the original black knob with engraved white shift pattern, complete with anti-vibration rubber insert.
-
Brake Adjuster and 2 Tappets Kit – Genuine Ap
- R429.54 excl VAT
- Genuine AP adjuster screw and wedges kit (not the cheap import, available}. Beware,This is a safety critical part and the cheap adjuster pins have a wrong angle and shape against the wedges making brakes inefficient after adjustment. Genuine AP braking parts are now all silver on this kit. The front brakes on 1959-64 with a single wheel cylinder and all…
-
Idler Gear 4 Sync Pre A+ Needle Roller Bearing
- R207.50 excl VAT
- Bearing 26.9mm wide to take 19.05mm idler gear shaft that fits in the gearbox case and clutch housing case on 4 synchro gearboxes until introduction of A plus when a larger bearing was fitted
-
Brake Pipe Clip for Front Subframe
- R18.64 excl VAT
- The clip that holds the brake pipe which runs across the front of the front subframe. Also used on some later injection cars to keep the wiring safe for spotlamps.
-
Door Pull Handle 1100
- R177.06 excl VAT
-
Brake Master Cylinder Repair Kit Fits Gmc171/2 Pre 85
- R352.40 excl VAT
- Almost every Mini built prior to the dual circuit system uses a .70" bore master cylinder. This kit fits them all. The original size in the '59-'64 Mini was .75" but as most of these cylinders have been replaced with the .70" size it is best to check the very early models. This seal kit has 1 ring seal and…
-
Hex Head Nut For 2010 Onwards Mamba Wheels
- R56.76 excl VAT
- HEX HEAD NUT FOR 2010 ON MAMBA WHEELS BOTH 6X10 AND 6X12 WHEELS
-
Door Plate Buffer Screw ( Short )
- R12.80 excl VAT
- SPECIAL 6/32" UNC COUNTERSUNK POZI SCREW 1/4" LONG FOR HOLDING THE 14A6835 BUFFER PLATE TO BODY.
-
Headlight Switch 1976-1997 Models
- R294.80 excl VAT
- Replacement headlight switch as fitted to all models from 1976 until 1997.
-
P700 Head Lights (Pair)
- R2,636.08 excl VAT
- Retro 1960's period look classic headlamp complete with metal triangle behind the lens, these will look truly fantastic on your Mini. ** Sold as a Pair **
-
Stick On Emblem Austin for Gear Knob
- R35.66 excl VAT
- Original Autin emblem stick on logo for use on gearlever knobs and key fobs sold by us. About 27.4mm wide.
-
Powerspark Electronic Ignition Kit (Negative Earth) to Suit Lucas 25D Distributor
- R1,073.70 excl VAT
- K2 & R1 - Powerspark Electronic Ignition Kit (Negative Earth) to suit Lucas 25D 23D Distributor This electronic kit is designed to replace the points and condenser inside a Lucas 25D distributor, giving you electronic ignition at the turn of your key. The Lucas 23D or 25D Distributor was fitted to many classic vehicles from Austin, Hillman, Land Rover, MG,…
-
Clutch Release Bearing – Heavy Duty Pre Verto
- R388.40 excl VAT
- Heavy duty clutch release bearing with a wider surface area, helps to spread even pressure on the clutch diaphragm and is favoured by racers.
-
Manifold to Downpipe Exhaust Clamp
- R100.00 excl VAT
- Exhaust manifold to downpipe clamp. The key to eliminating exhaust leaks at the manifold flange is the clamp. These new clamps include proper brass nuts and support washers. Fits most 850cc, 948cc, 998 etc. Those engines with single carb and cast iron manifold. For the original and best sealing type see part number GEX7046CAST.
