Fittings
-
Master Cylinder Clevis Pin
- R27.20 excl VAT
- This should have a split pin in it and attaches to your foot pedal that operates the master cylinder.
-
CLUTCH OIL SEAL UPTO 1992
- R82.74 excl VAT
- See‚ 13H2934MS‚ for original silicon type best seal available, which is Mini Spares own copy of the original Gaco seal that was discontinued. These were the seals used on production/rally /race cars that never gave problems. This seal is the standard aftermarket item and adequate for standard use. Fits every mini except automatic but in 1992 the factory replaced this…
-
Clutch Oil Seal Minispares Performance Use Type.
- R123.83 excl VAT
- Introduced for competition engines where the increased rev limits or temperature can cause the‚ LUF10005‚ or‚ 13H2934‚ to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is identified by numbers 1042 and 55 70 10 with crank rotation arrow. The factory changed the seal in 1992 to the type with…
-
Clutch Return Spring
- R58.20 excl VAT
- Clutch arm return spring for the return of the slave cylinder push rod.
-
Master Cylinder Plastic Cap (Sold Individually)
- R140.20 excl VAT
- Genuine plastic cap as supplied on single line brake cylinders pre 1976 and all clutch masters. It doesn't often break or wear out, but it gets lost or turns yellow. The early steel master cylinder reservoir caps had a tendency to rust on, so this white plastic could be considered an upgrade unless you wish to keep your Pre 1963…
-
Clutch Lever Arm Top Clevis Pin
- R46.74 excl VAT
- Upper clutch lever arms clevis pin, suitable for both verto and non verto arms. Split pin for common clevis pin list, GFK101 for CLZ409 handbrake levers to cable on rear drum GFK102 most mini clevis pins except CLZ409 GHF510 for GCV1105 CV joint and rear hub nut GHF511 for GCV1013 CV joint
-
Adjustable Clutch Slave Cylinder Push Rod
- R539.60 excl VAT
- Classic Mini adjustable clutch slave cylinder push rod.
-
Clutch Flywheel Drive Strap
- R115.80 excl VAT
- These are the straps held on by‚ 2A3659‚ bolts on the diaphragn type flywheel. There are 2 per bolt making 6 in total as standard but on performance flywheel and clutches we recommend 3 straps per bolt to minimise stretching. Check the holes and finish so bolts enter freely as they sometimes are roughly finished.Only use C-2A3659 and C-2A3659 bolts…
-
Clutch Plunger – Pre Verto (Round End)
- R297.90 excl VAT
- Clutch release plunger-This is the carrier that holds the clutch release bearing and on the other end has a hole for the clutch lever arm‚ 22A2204MS. If you are looking for an upgraded product see 22A180.
-
Bolt Clutch End Cover – UNC
- R41.00 excl VAT
- Bolt for holding the Clutch End cover (Wok) onto the flywheel housing. Also for the CHM85 differential side cover 1" long unc 5/16" bolt. A plus type bolt with built in washer on head, known as flanged head bolt. DAM7756 is slightly longer with thread lock used on late cars.
-
Washer Copper Brake/Clutch Union
- R39.40 excl VAT
- 1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a‚ 233220A.
-
Clutch Oil Seal for Injection and 1992 On HIF38 Carb Model
- R153.06 excl VAT
- Genuine Mini Spares product in Viton.This oil seal was introduced in 1991 with the first injection models and the HIF38 carb version cars and has the internal spring closer to the back. Meant to help with extra crankcase pressures and nips up slightly tighter, it has been found to leak on extra high performance engines and the 13H2934MS is favoured…
-
Clutch Flywheel Strap Bolt Short – Torque to 16lbs Only
- R65.11 excl VAT
- There are 3 of these shorter 5/16"unf bolts holding the spring straps‚ 2A3658‚ to the flywheel on diaphragm type flywheels only. Not for Verto flywheel. Only tighten up to 16lbs per sq foot torque when using shake proof washer or 18lbs if using flat washer and locktite. The steel used is EN1A leaded which is a low carbon free cutting…
-
Clutch Master Cylinder Gasket
- R44.33 excl VAT
- This gasket sits under the clutch master cylinder. For brake master cylinders see 31G840.
-
Flywheel Bolt Pre Verto
- R288.12 excl VAT
- The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by‚ 22A1155‚ locktab on the‚ 88G508‚ key washer.
