Fittings & Seals
-
Boot Lid Seal Clip for 14A6584 (26 Required)
- R18.50 excl VAT
- Used on all MK1/2/3 bootlids where there are 26 little holes drilled around the inner edge. These are for use with 14A6585 seal--- Later cars 1988 on fitted a seal to the body only (cke10018)
-
Manifold Stud. Suitable for All Non Injection Minis
- R21.15 excl VAT
- Manifold stud 39mm long for all A series engines up to injection which use LYR10028 which is 6mm longer at 45mm.
-
Rubber Grommet for Floor Pan & Boot Floor 1″ 25 mm
- R44.11 excl VAT
- Special shape and strength 1" rubber floor plug. Also speedo cable unused hole where shells have holes for LHD and RHD.
-
Boot Lid Hinge Gasket Upper
- R24.29 excl VAT
- These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
-
Door Gasket External Hinge Large End On Door
- R19.70 excl VAT
- THIS IS THE LARGE GASKET THAT FITS BEHIND THE HINGE ON THE DOOR OF AN EXTERNAL HINGE ON CARS WITH SLIDING WINDOWS SUCH AS MK1/2. SEE BMP135 FOR SMALL ONE.
-
Boot Hinge Gasket Lower
- R14.47 excl VAT
- These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
-
Boot Lid Seal Early Type (Requires 26 X 14A6585)
- R369.01 excl VAT
- Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid all the way round. Fitting the wrong way round makes it very difficult to close lid…
-
Barrel Lock Set for Push Button Type Door Handles 1970 on
- R747.10 excl VAT
- Key barrel set for Mk3 onwards door handles and boot handles.
-
Bootlid Number Plate Buffer
- R62.94 excl VAT
- All Mk1/2 had a hinged number plate on the bootlid and these are the buffers that protect your paintwork and help locate the number plate at the correct angle. 2 required per car, sold individually.
-
Boot Seal Clip Kit
- R371.20 excl VAT
- Introduced by the factory to eradicate water getting to the electric coils causing breakdowns this was used up until they introduced the plastic engine protection shield but many owners still played safe and fitted one anyway. Note: The kit contains 26 clips needed for 1 car
-
Bootlid Seal, 1988 to 2000
- R297.72 excl VAT
- This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.
-
Mini Boot Lid Liner with screws – Black
- R1,426.00 excl VAT
- This Boot Lid board will fit any Mini saloon boot lid. When fitted it looks very attractive with the set of screws and cupwashers finishing it off! INSTRUCTIONS Initially mount the board on the boot lid, mark where you need to drill 1/8" holes for the screws. Easy! Manufactured by the world famous Newton Commercial Interior.
-
Boot Hinge Gasket 1275e
- R45.00 excl VAT
- These screws fit the lower 2 holes on all boot hinges.Also see 24A2175/6 gaskets that you will need. 1/4" unf 5/8"long, also for tailgate stays on pickup. Note: Locally produced and 1 set will complete 1 car.
-
Grommet for Boot Floor 8 mm 5/16
- R23.93 excl VAT
- Rubber blanking plug 5/8"wide to fit boot floor hole 5/16".
-
Boot Seal-Elf/Hornet
- R923.54 excl VAT
- Riley and Wolseley models.
