Mini
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
-
Valve Stem Oil Seal As Used On MPi Models
- R33.41 excl VAT
- Rated 0 out of 5
- Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking. Manufactured using original Dupont Viton which offers excellent resistance to heat, aggressive fuels and chemicals. A "must" for the…
-
Wheel Nut No6 Large Seat Chrome (Larger Cn1 Equivalent)
- R56.08 excl VAT
- Rated 0 out of 5
- The original stock nut has a very small area of contact to absorb all the loads of cornering, etc. Our special "wide seat" nuts almost double the contact area! The first designs (Bugeye) use a flatter seat than the more common "Rostyle" type. Chrome lug nuts are now available for any option.
-
Wheel Nut Pre 60° Angle 10″ Steel Wheel (Rounded)
- R27.48 excl VAT
- Rated 0 out of 5
- The original mini wheel nut with a round seating was fitted from 1959 until 1984 when they changed to a 60 Degree straight seating wall. This later nut was 113087. 10" wheels with plastic hub caps used a strange looking nut to hold the cap FAM5701. Supplied individually.
-
Coil for Non Ballast / Points Ign Up to 1983
- R597.95 excl VAT
- Rated 0 out of 5
- Original mini coil fitted to all cars up to 1983. 3ohms NOT for ballast type ignition systems. Our research, sales and feedback shows Intermotor coils to be the best available for the mini. Original type coil bracket 12G2994 with welded on lug nuts is available as fitted from 1969-1995
-
Screw Brake Drum and Mini Std/Duplex Front Plate
- R13.07 excl VAT
- Rated 0 out of 5
- The screw that holds the drum on the hub. Earlier hubs had two screws, many replacements have only one, all that’s needed.
-
Ball Joint Kit.Mini – Genuine Mini Spares Part
- R317.84 excl VAT
- Rated 0 out of 5
- The Mini is the classic front wheel drive,heavy engine unit in the front car that really abuses the front suspension and the entire load is transmitted through the top and bottom ball joints. They do wear and should be inspected when you're working on the CVs or wheel bearings
-
Clip For Inner Door Moulding Mk3 On
- R20.03 excl VAT
- Rated 0 out of 5
- Trim clip for fitting the stainless/rubber window moulding (EJU10003) on to the door. Sold individually.
-
Wheel Stud (55mm) Cooper S and All 1984 On Rear
- R28.39 excl VAT
- Rated 0 out of 5
- This is the correct length for all minis using the rear spacered type drum which was fitted to all Cooper "S" 1275GT and every mini from 1984 to 1996 except the ERA Turbo and Sportspac cars which had 13" wheels. Stud shank length from under head of bolt is 55mm with 20mm thread. Next size up is ENJO-1039.
-
Core Plug 1300 & All A+ Engines
- R26.44 excl VAT
- Rated 0 out of 5
- Cup type core plug for all A plus and 1275cc engines except for Cooper S. 33.6mm wide.A plus 5 required but only 4 on 998 A plus. 1275 has 2 core plugs oil pump end of block whereas 998 only has one
-
Manifold Stud. Suitable for All Non Injection Minis
- R21.15 excl VAT
- Rated 0 out of 5
- Manifold stud 39mm long for all A series engines up to injection which use LYR10028 which is 6mm longer at 45mm.
-
Single Bullet Connector for Wiring Looms
- R21.23 excl VAT
- Rated 0 out of 5
- Single bullet connector used to join the front loom to the rear loom near the wiper motor.
-
Seam Moulding Clip Stainless Steel
- R12.80 excl VAT
- Rated 0 out of 5
- This is the longer type cylinder head adaptor tube which allows fitment of the by pass hose without removing the head. The shortened hose GZA2083 slides up the tube and then back down on the water pump tube. Frequently rusted on old heads and not even there on newer heads. These are 5/8"uns x 16tpi "whitworth fine" thread and if…
-
Boot Lid Seal Clip for 14A6584 (26 Required)
- R17.53 excl VAT
- Rated 0 out of 5
- Used on all MK1/2/3 bootlids where there are 26 little holes drilled around the inner edge. These are for use with 14A6585 seal--- Later cars 1988 on fitted a seal to the body only (cke10018)
-
Wheel Nut No5 Large Seat Chrome 60° Taper 1984 On
- R50.01 excl VAT
- Rated 0 out of 5
- If your wheels are using a tapered seat style wheel nut you must consider this latest safety option! The original stock nut has a very small area of contact to absorb all the loads of cornering, etc. Our special "wide seat" nuts almost double the contact area! Sold singly.
-
Hub Kit Front With Seals &Amp; Split Pin Non Genuine
- R351.24 excl VAT
- Rated 0 out of 5
- Cheaper alternative to genuine timken front bearing kits. These are very well tried and the best of any of non genuine bearings available. Sold as one hub kit only. Please note-for arduous or race use Timken bearings in genuine GHK1140 are matched pairs with spacer all size tested under load and stress which is why they are more expensive and…