Cooling & Heating
- Sorry, this product cannot be purchased.
-
Radiator Lower Hose Without Heater Take Off Pipe
- R222.00 excl VAT
- True Kevlar strands with 2 year guarantee.Fitted as standard in some of the hot countries before heaters became standard fitment this hose has the elbow joint missing that connected to the half inch heater hose. A favourite for racers and competion engines where heaters are no longer required as it cuts out an extra problem area.
-
74° Thermostat
- R123.00 excl VAT
- This is the lowest temperature stock thermostat, ideal for hot climates or summer fitment with 82 degrees for winter, the ideal temperature commensurate with optimum power output is 65-70 degrees. However this is not practical for road applications. The lowest thermostat available is 75 degrees and should be the lowest one considered. 82 degrees is a much better choice with…
-
Cooper S Kevlar Reinforced Top Hose
- R150.20 excl VAT
- 1275cc engine top hose in Rubber with Kevlar reinforcement. Kevlar is a high tech aramid fibre produced by Dupont co in USA. It is longer lasting, stronger with less heat transfer and wear resistance.Not only does this hose fit the Original Cooper S models, it is also required when fitting 1275cc engines into a round front Mini in conjunction with…
-
Super Water Pump Large Impeller 3 Year Guarantee
- 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with a high quality die cast body. A Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped. Fitted with a PPS, glass filled plastic impeller as used by Aston Martin and Jaguar it reduces weight on the bearing loading and has a triple lip seal giving…
-
11 Blade Yellow Plastic Radiator Cooling Fan
- Genuine Rover part from BMH. 11 blade plastic fan, one of the most efficient fans ever fitted to a Mini. This fan pushes a lot of air with very little noise. If you need more air, then please see part#‚ 2A998. This Hot Climate fan pushes even more air but it is substantially louder than the 11 blade version. Make…
-
By Pass Hose Fluted Easy Fit
- If you drive A-Series cars long enough you will eventually have to replace the water pump bypass hose. These are the best quality available to fit without removing the cylinder head but these fluted rubber hoses have a bad reputation so if possible fit a kevlar type. This can be done by fitting a 12A2075‚ tube in the head and…
-
82° Thermostat
- R113.00 excl VAT
- Mid-range stock thermostat fitted until 1990 1275cc. The lowest thermostat available is 74 degrees and should be the lowest one considered - 82 degrees is a much better choice with an 88 degree alternative for winter driving and those with economy as the main consideration. The higher temperature the more thermally efficient the engine becomes. It is possible to run…
-
Thermostat Blanking Sleeve
- Removal of the thermostat helps to reduce engine temperature, however a thermostat blanking sleeve should be fitted to maintain correct coolant circulation to the entire head. Failure to do so will cause overheating around #3 and 4 combustion chambers, with obviously disastrous results. When the blanking sleeve is used it is also necessary to blank off the by-pass hose (not…
-
Radiator Top Kevlar Hose Grh469.1275GT Or Cut for All 1275cc
- Reinforced in kevlar for longevity as standard rubber hoses seem to be poor quality these days. This is not the true strand kevlar hose we use in‚ GRH240KEVLAR‚ bottom hose.This has a longer radiator end than the cooper S and other 1275cc engines owing to the spacing of the radiator on the 1275GT clubman model. Can cut down to required…
-
Radiator Cap, Lev – R – Vent, Steel 16 psi
- This radiator cap is designed to prevent your car from boiling over at a lower temperature. It has a pressure release lever to allow the pressure to escape, and it is made from premium materials to meet the original equipment specifications. more details Key Features - The SWIV-EL design allows the cap to be installed and removed much easier than…
-
Oil Pressure Switch Mini and Metro
- Fits every A series engine from 1959-1996 (except twin point injection minis) they have a different switch GPS135 and also have a transducer for oil temperature (YCB100320). These original type oil switches came on when oil pressure dropped below 7-10lbs but if you require earlier warning than that then use HPS1 which activates at about 22lb or HPS3 which is…
-
Radiator Original Shape In Alloy Pre 1991
- Alloy lightweight original looking radiator with correct shape header and lower tanks, same as ARP2000 to look at but made in alloy with latest technology cuprobraze manufacture. Metric fixings see FS106107. Painted black so they look original and cover any blemishes from preparation and manufacturing. Cheapest high quality alloy radiator available anywhere. Rave reviews from race and road users for…
-
Radiator Cap 13lb Up to 1980
- The original highest pressure cap as used on the 1275 cooper S until they decided to fit 88 degree thermostats and 15LB rad caps on A plus units.
-
Rad Cap 15lb 1980–92. Except Expansion Tanks
- Fitted from A plus on to increase engine running temperature. If your radiator has a sender unit in the bottom you may have an expansion tank and therefore the radiator will need a better sealing pressure cap which allows a small vacuumGRC207.
-
SUPER WATER PUMP LARGE CAST IMPELLER
- Large impeller high capacity water pump moves a greater volume of coolant than the standard water pump. Fits all Minis except early 850/997cc which will require modification. Includes gasket The rubber bypass hose is sold separately. See part number GZA2086
-
Radiator Lower Kevlar Hose- 2 Year Warranty
- Real Kevlar stranded hose,2 year guarantee-the only true Kevlar threaded hose available where you can see the strands, it is made for longevity and low heat transfer making this the best selling bottom hose in the market. The built in property of kevlar makes it much stronger. The ultimate hose apart from C-GRH240 silicon type.This was a new Mini Spares…
-
Radiator Mini & Cooper – Pre 1991
- Standard Mini radiator with 3 offset tubes in the core. Metric thread fixings. Flanged metric thread bolts are available as FS106107. See also, alloy radiator in same shape but 2x18mm tubes as an alternative ARP1110 for better cooling in summertime or warmer climates. See ARP1106 for 3 inline bore super coool rad as used by some Historic racers(although many still…
-
Super Water Pump Less By Pass – 3 Year Guarantee – Pre MPi
- 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped. Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Martin it reduces weight on the bearing loading and with a triple lip seal gives a…
-
Radiator Lower Hose (Ex Clubmans)
- Bottom radiator hose suitable for- Classic Minis (not Clubman) installed with a heater from 1959-92
-
Genuine Water Pump Gasket
- Genuine water pump gasket, green one side and grey the other, grey side to the water pump.
-
Radiator 2-Core Aluminium (Any Side Fitting Type)
- Mini Spares own exclusive designed Lightweight aluminium type high efficiency radiator with good fitment, rigidity and appearance, unlike others on the market with 4 large ugly fixing nuts on each side, or where the header tank is 10mm wider that fouls the cowlings. The lower hose outlet is also positioned correctly to fit all the Coopers and 1275 engines and…
-
Flanged bolt for heat shield m6x10( rad bolt )
- m6x10 bolt--ideal for radiators with metric fittings (6 required for rads) original imperial radiator screws were SH604031
-
Heater Valve Genuine Minispares Original Shape
- Genuine Mini Spares heater valve. The original RANCO tooling has been scrappped so beware of some imports available where the inners quickly explode loosing the metal cap and all your water when operated.This has M4 metric thread bolt included for the cable screw instead of the 11/31"unc thread original For the straight stem version of this valve see 13H5506. For…
-
Radiator Top Bracket 1275 Stainless Steel 304
- The upper radiator bracket was different on clubman's and was wider owing to the fact that a spacer was often used on the fan blade for clearance. Made out of SS304 and Laser Cut "Mini"
-
Super Water Pump Large Cast Impeller (Less Bypass)
- Water Pump without Bypass, includes gasket.
-
Classic Mini Radiator 3 Row
- Classic Mini Radiator Original Style 3 core Suitable for all Classic Mini from 1964-1992 High quality, original style 3 core radiator An affordable authentic brass copper construction Excellent fitment, manufactured to best quality Application/Fitment: All Classic Mini 1964-1992 (Please note: Not suitable for 998 Cooper Cooper S (normal 998 are OK),or vehicles retrofitted with Cooper vibration damper pulley)
-
Rad Cap for Expansion Tank
- Metal type expansion or rad cap with no pressure spring, commonly used on race prepared cars and all Austin -Morros 1100/1200 derivatives plus Aussie Mokes.
-
Heater Tap Gasket
- R16.41 excl VAT
- This gasket fits on the cylinder head for every A series heater valve or outlet pipe until the hole was no longer drilled when they changed to a heater valve fitted into the hose line from 1990 on.
-
Rad Top Bracket Grommet And Lower On 2 Piece Cowlings
- This grommet is used on all top radiator to cylinder head brackets plus the bottom bracket on earlier two-piece radiator cowlings. It replaced the CAM4414 flatter bush originally fitted to the top bracket from 1974 on one-piece cowlings.
-
Castrol 5L GTX 20W-50 Motor Oil – High Mileage
- Castrol GTX is a premium conventional motor oil that has been helping to extend engine life for over 50 years. It has evolved to meet the needs of consumers and vehicle manufacturers since 1968 and continues to innovate and remain a trusted brand today.
