Fuel
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
-
Carb Gasket Su Float Chamber
- R28.89 excl VAT
- Rated 0 out of 5
- Paper gasket for the float bowl of any HS2/HS4/HS6 carbs.
-
Petrol Tank Seal For Fuel Level Sender Unit
- R49.56 excl VAT
- Rated 0 out of 5
- Seal for Saloon petrol tank sender unit and the retainer clip is ARA1501. Early type tanks had 6 screws holding the sender unit in place and the gasket is GUG705711GM. .
-
Accelerator Pedal Rubber Pre 1976
- R38.80 excl VAT
- Rated 0 out of 5
- Accelerator pedal rubber pad for Mini pre1976 or Morris Minor.
-
Genuine Minispares Fuel Filler Neck Grommet (Sold Individually)
- R246.00 excl VAT
- Rated 0 out of 5
- Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as used pre 1997 and made in the UK using high quality EPDM for better looks…
-
Locking Petrol Cap – Vented
- R400.60 excl VAT
- Rated 0 out of 5
- For all mini pickups, vans, estates and MK1/2 Minis. Any early minis without a vent on the top of the tank can also use this cap. A vented cap has been fitted to Minis during its history but must not be fitted to any Injection cars as they require a sealed system. See WLD100660 for non vented cap.
-
Petrol Tank Sender Unit. Saloon Up To Injection
- R868.98 excl VAT
- Rated 0 out of 5
- Fuel tank sender unit for saloons up from 1964 to 1992 when a voltage stabiliser was fitted.1964 built cars could have had a similar locking ring type but if no voltage stabiliser fitted on back of speedo they fitted a ARA959 which is obsolete. XNB10007 does not include sealing ring or locking ring. Pre 1964 six bolt type is 2A2163.
-
Petrol Cap Chrome Vented Saloon Non Locking
- R152.79 excl VAT
- Rated 0 out of 5
- Not for injection type cars.The original shape/type chrome cap used on the mini, this is vented and non locking. Originals were non vented on saloon and vented on Van/Estate. Quantity required is one unless you have a saloon with twin tanks (2 required)
-
Petrol Cap With Aston Look For Pre ’96 Cars
- R564.60 excl VAT
- Rated 0 out of 5
- This cap fixes to the petrol tank neck so that the genuine locking cap fits snuggly inside so that both pieces cannot be stolen. Ultra easy to install and looks fantastic. Large 3.5" face! Designed to look expensive, this '60s style cap features a flip-up top that uncovers a locking gas cap. The whole unit installs and opens as easy…
-
Fuel Pump Mechanical Pre 1990 Cars And All 998 Non Genuine
- R731.62 excl VAT
- Rated 0 out of 5
- Drives off the camshaft at the rear of the motor. These pumps are generally reliable but when a diaphragm goes bad it can be very bad as often raw petrol is pumped into the engine.This dilutes the oil and causes severe wear. When fitting, make sure the pump lever is on the cam lobe not to the side.
-
Throttle Return Spring for Twin Carbs
- R38.41 excl VAT
- Rated 0 out of 5
- Throttle return springs for all twin carb variants. Usually 3 fitted.
-
Accelerator Return Spring for Hs2/4 Carb
- R57.90 excl VAT
- Rated 0 out of 5
- This throttle return spring fitted every HS2/4 single SU carb and also on the twins as fitted by the factory. Twin carbs used AEC2075 for choke return.
-
Sandwich Plate for Weber DCOE 40mm
- R80.00 excl VAT
- Rated 0 out of 5
- This is used to ensure enough flexibility to prevent high frequency vibrations being transmitted to the fuel in the float chamber, whilst preventing air being drawn in.
-
Sandwich Plate for Weber DCOE 45mm
- R80.00 excl VAT
- Rated 0 out of 5
- This is used to ensure enough flexibility to prevent high frequency vibrations being transmitted to the fuel in the float chamber, whilst preventing air being drawn in.
-
Su Carb Float Top Screw
- R19.76 excl VAT
- Rated 0 out of 5
- The proper slot head screw for the SU dashpot and float lid 3/16 whitworth thread.
-
Stud Hs4/Hif Carb + Some 12g103 Housing (5/16″)
- R36.72 excl VAT
- Rated 0 out of 5
- Universal stud made for fitting the HS4/HIF carb to the manifold (except HS6 with alloy spacer on cast one piece manifold which requires CHS2515 (5.8mm longer)) and it also fits the cylinder head to take the thermostat housing. Note that HS2 carbs require larger CHS2613/4 studs, 5/16" unc with unf thread for nut.