Manifolds
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
Home » Shop » Mini » Exhaust & Manifold » Manifolds
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
-
Alloy Water Heated Torquemaster Inlet Manifold Hs4/6 Hif38/4
- R1,171.60 excl VAT
- Rated 0 out of 5
- Genuine mini Spares inlet manifold dyno tested and designed for our Stage one kit‚ C-STN17. The single SU manifolds is developed to give maximum airflow and gas speed, yet fit all engines even if the standard air cleaner set-up is used. It has 1/2" pipe through it for heating with water and the as-cast finish provides maximum fuel atomization. C-AHT770…
-
Manifold Std Bore Exhaust Long Centre Branch (LCB) Maniflow
- R3,376.48 excl VAT
- Rated 0 out of 5
- Standard bore LCB (1-3/4"id) that is ideal for very hot small bore engines, for standard to high performance 1275s and for street 1380s. There is NOT enough clearance room when fitting to old cars with rubber couplings which foul. Using QL5000 type couplings will help but re=shapinng of manifold is still required in most cases. Alternatively we offer C-AEG362 especially…
-
Coil Rubber Cover 1959 – 1996 for Conventional Shaped Coil
- R164.20 excl VAT
- Rated 0 out of 5
- Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG which is a superior gasket for performance use and easier to remove when replacing as it does not stick to head very…
-
Manifold Gasket for Fuel Injected Cars
- R168.82 excl VAT
- Rated 0 out of 5
- Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.  
-
Exhaust System With Twin Box for Saloon Small Bore
- R3,876.24 excl VAT
- Rated 0 out of 5
- Twin box exhaust system for all 850/998/1100 saloons Now designed by our RC40 team as a 2 piece system for easier fitment and transportation, this fits from the original cast iron inlet/exhaust manifold right to the rear bumper on any saloon including early floor start cars,it has the GEX7053 front clamp and GEX7052 centre clamp plus the joining U clamp…
-
Manifold Inlet Weber 45 DCOE 3.5″ Maniflow Steel
- R5,962.54 excl VAT
- Rated 0 out of 5
- 3.5" long steel intake manifold by Maniflow for Weber 45 DCOE/DHLA
-
Manifold Clamp 1.75″ Cooper Freeflow With Tag Flat Type
- R164.59 excl VAT
- Rated 0 out of 5
- This is the clamp on the cooper freeflow manifold to clamp it to the engine for extra support, supplied with tag.
-
Blanking Plug Inlet Manifold & Cyl Head
- R115.16 excl VAT
- Rated 0 out of 5
- This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will not blank off the by pass hose thread as it is a different thread-see 88G619. 7/8" 22mm head size.
-
Plug 5/8UNF X 5/8 Screw Inlet Manifold
- R32.84 excl VAT
- Rated 0 out of 5
- This plug fits our inlet manifolds and Rover types with servo take off holes.. 5/8 UNF grub screw that use 8mm allen key for blanking inlet servo take off or temp transmitter hole at front of pre 1996 cylinder heads. Can also use ADP210