Drivetrain
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
-
Hub Kit Front With Seals &Amp; Split Pin Non Genuine
- R351.24 excl VAT
- Rated 0 out of 5
- Cheaper alternative to genuine timken front bearing kits. These are very well tried and the best of any of non genuine bearings available. Sold as one hub kit only. Please note-for arduous or race use Timken bearings in genuine GHK1140 are matched pairs with spacer all size tested under load and stress which is why they are more expensive and…
-
Hub Kit Rear Inc Seals (Non Genuine)
- R367.00 excl VAT
- Rated 0 out of 5
- Rear tapered roller wheel bearing kit, for one wheel. Not genuine Timken type but a copy. These can be used on any Mini. Kit includes inner and outer bearings with spacer plus seals and split pin. If you are into preventative maintenance, then the tapered bearings are much easier to remove and re-pack than the ball bearing type. Stronger design,…
-
Front Wheel Hub Kit Drum Brake And Cooper 997/998 Only
- R361.80 excl VAT
- Rated 0 out of 5
- Front wheel bearing kit, ball bearing type, for one Mini wheel. Kit includes inner and outer bearings with built in spacer and seals. The spacer clip‚ 2A4361‚ has been made obsolete from Rover for many years and does not require to be fitted when these bearings are used.
-
Screw Drive Flange Cooper S
- R11.40 excl VAT
- Rated 0 out of 5
- Countersunk crosshead screw. 1/4"unf / 16mm(3/8") total length. To hold the drive flange to the brake disc on the Cooper S type 7.5" wide brake set up. Also holds striker plate for door.
-
Pot Joint Gaiter Kit. Non Genuine
- R122.44 excl VAT
- Rated 0 out of 5
- In board CV joint(pot joint) gaiter kit with plastic clips and grease. Non Genuine item many sell as GSV1073. The single largest reason for the failure of this rugged assembly is contamination, dirt and moisture will destroy one very quickly. This inbooard CV rubber boot protects the joint at all angles but if your boot shows any sign of cracking…
-
Cv Joint Gaiter Kit Universal For Any Mini
- R72.64 excl VAT
- Rated 0 out of 5
- One gaiter, 2 plastic clips and grease. The single largest reason for the failure of this rugged assembly is contamination. Dirt and moisture will destroy one very quickly. The CV rubber boot protects the joint at all angles but if your boot shows any sign of cracking or scuffing preventative replacement can save a lot of money. This type is…
-
Drive Flange En24 Material – Cooper S & Early 1275GT
- R641.38 excl VAT
- Rated 0 out of 5
- Mini Spares own quality UK made product from original drawings in standard material for 7.5" wide disc set ups. The Mini Cooper "S" drive flange as used on all 7.5" disc Cooper S/1275GT variants was originally intended to use 10" wheels as an integral part of the front suspension. In addition to providing the connection between the axle and the…
-
CV Joints 850/998 CV Joint Plus 997/8 Cooper
- R650.00 excl VAT
- Rated 0 out of 5
- Smaller type CV joint and gaiter kit with the One and a 16th inch hub nut, 1.125"(28.58mm)used on drum brake minis pre 1984 and Cooper 997/998.
-
Hub Nut Split Washer for CV Joint
- R113.83 excl VAT
- Rated 0 out of 5
- Original genuine sintered split washer for behind the hub nut that goes on the cv joint drive flange. This is not the cheap old metal type often sold by our competitors which Rover discontinued and changed to sintered for all production cars and spare parts. Fitted on all minis with the large type cv joint GCV1013 when disc brakes are…
-
Drive Flange Bolt 12″ Wheel
- R46.76 excl VAT
- Rated 0 out of 5
- 4 are required for the drive flange to 8.4" disc set ups and is also the same bolt for limited slip diff crownwheels. 3/8" UNF THREAD 11/16" long. Sold singly
-
CV Joints Disk – Outer
- R560.00 excl VAT
- Rated 0 out of 5
-
Pot Joint Inboard CV Joint – Non Genuine
- R767.08 excl VAT
- Rated 0 out of 5
- Non genuine aftermarket only as the genuine originals are obsolete. These are the best on the market where clip grooves are in the correct place to save the driveshaft seizing on. Later model Minis have CVs on both ends of the axle
-
Front Outer Wheel Bearing Seal
- R38.12 excl VAT
- Rated 0 out of 5
- Mini front hub inner bearing seal
-
Cv Joint Gaiter Drum Type
- R207.80 excl VAT
- Rated 0 out of 5
- CV joint gaiter kit for the small joint as used on drum brake minis and standard 997/8 coopers with 1.1250" hub nut. The same heavy duty rubber as supplied with our CV joints.
-
CV Joint With Hub Nut. Gaiter and Circlip
- R851.68 excl VAT
- Rated 0 out of 5
- Mini Spares own stamped GCV1013. Brand new CV Joints with gaiter, hub nut, grease and clips. Stamped with our part number GCV1013 for identification from may 2014 to denote our authenticity of this top quality joint, sold singly. These are the best joints available that we have tested since the demise of the original Birfield Hardy Spicer tooling,(GKN) -beware of…