Fittings & Seals
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
Categories
- Mini
- Accessories
- Badges & Stickers
- Battery
- Body
- Brakes
- Cables
- Clutch
- Cooling & Heating
- Drivetrain
- Electrics
- Engine
- Exhaust & Manifold
- Fasteners
- Filters
- Fuel
- Gauges
- Gearbox
- Grilles & Brightwork
- Interior
- Steering
- Subframe
- Suspension
- Water
- Wheels
- Shop Soiled
-
Clip For Inner Door Moulding Mk3 On
- R20.03 excl VAT
- Rated 0 out of 5
- Trim clip for fitting the stainless/rubber window moulding (EJU10003) on to the door. Sold individually.
-
Seam Moulding Clip Stainless Steel
- R12.80 excl VAT
- Rated 0 out of 5
- This is the longer type cylinder head adaptor tube which allows fitment of the by pass hose without removing the head. The shortened hose GZA2083 slides up the tube and then back down on the water pump tube. Frequently rusted on old heads and not even there on newer heads. These are 5/8"uns x 16tpi "whitworth fine" thread and if…
-
Door Surround Seal Mk1 & Mk2
- R313.03 excl VAT
- Rated 0 out of 5
- Mkl Mini door seals were unique in both shape and texture, they had a natural rubber finish and a pronounced point on the sealing edge. These are the only seals that should be used on sliding window cars. Later seals are too big and place undue stress on the hinges. Similar to the original 24A1351 all rubber type but we…
-
Screw Door Hinge / Striker Plate Mk3 1969 On
- R11.96 excl VAT
- Rated 0 out of 5
- Countersunk, crosshead screw. 1/4"unf 19mm (3/4") total length. This screw fits the internal door hinges on wind up window cars and the striker plate on the B post.
-
Door Moulding Inner With Seal Mk3 On
- R474.40 excl VAT
- Rated 0 out of 5
- This is the 1/2" tall thinner type fited to wind up window cars from 1970 on.
-
Door Gasket External Hinge Small End On A Panel
- R17.38 excl VAT
- Rated 0 out of 5
- THIS IS THE SMALL DOOR HINGE GASKET ON THE A PANEL FOR SLIDING WINDOW TYPE DOORS.
-
Door Handle, Flanged Screw for Winder Handle CZA7109
- R35.62 excl VAT
- Rated 0 out of 5
- Special screw for CZA7109 handle only
-
Outer Door Weatherstrip Clip (Single)
- R16.14 excl VAT
- Rated 0 out of 5
- Lower Moulding clip for wind up window Mouldings. 4 PER SIDE required but sold singly-Fits CZH1666/7 and PAM1014/5 Also used for 24A1169 glove box Moulding MK1/2.
-
Door Moulding Outer With Seal L/H
- R485.13 excl VAT
- Rated 0 out of 5
- L/H outer brightwork trim with the seal attached to stop water seeping down into the door frame, on all cars with wind up windows from about 1980 on, these are the later type with the black protection ends fitted as a safety requirement on new cars.
-
Door Moulding Outer With Seal R/H
- R485.13 excl VAT
- Rated 0 out of 5
- R/H outer brightwork trim with the seal attached to stop water seeping down into the door frame, on all cars with wind up windows from about 1980 on, these are the later type with the black protection ends fitted as a safety requirement on new cars.
-
Door Mouldings Car Door Set 2 Of EJU10003 +1 Each CZH1666/7
- R1,837.60 excl VAT
- Rated 0 out of 5
- For wind up window cars 1970 on this is a set of inner and outer door brightwork mouldings with rubber seals attached to stop water running down the windows causing rust and to prevent draughts, including fitting clips. The outer mouldings are the earlier better looking original type as fitted to Cooper S MK3 without the black plastic ends which…
-
Door Opening Handle Black Plastic
- R148.93 excl VAT
- Rated 0 out of 5
- This plastic handle fitted any wind up window cars up to the introduction of the twin points, which then changed and the handle fitted from 1996 on is now obsolete.
-
Bonnet Strap Tan Original Works Type-Single Strap
- R397.04 excl VAT
- Rated 0 out of 5
- This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. Original light colour Tan leather 3.3mm thick from the tanneries for use on horse bridles, with alloy fastening. Screws included. Mini Spares have been supplying these original looking type for over ten years so beware of copies which are thinner with inferior…
-
Hinge Pin for External Hinge Mk1/2
- R28.66 excl VAT
- Rated 0 out of 5
- It is possible and almost easy to repair sagging Mkl Mini door hinges . You don't even have to remove the hinges from the car. Once you have removed the original hinge pin you simply drill a hole in the front hinge half, push in the bush and reassemble with the new pin (sometimes you find that job has been…
-
Mk1 & Mk2 Door Striker Nylon Buffer
- R70.42 excl VAT
- Rated 0 out of 5
- White plastic/nylon buffer on door of all UK external hinge minis. The door striker plate 14A6832 holds the door shut, but the nylon guide block actually supports the weight when the door is closed. When one wears it typically takes the other with it, so replace both. Don't forget to replace the plate 14A6834 that sits in the recess which…